Which grade is best for me?
Fillerina 12HA is available in two different concentrations, selected according to the condition of the skin and wrinkles: Grade 4, Grade 5.
Grade 4 is best suited for you if you have:
– Deep wrinkles and expression lines
– Aging-related wrinkles with visible, noticeable, and uneven microrelief
– Noticeable skin depression and tissue depletion
– Skin with poor thickness, density, and elasticity
– Visible signs of sagging
– A need for more volume in the cheekbones and lips
Grade 5 is best suited for you if you have:
– Very deep wrinkles and expression lines
– Aging-related wrinkles with highly noticeable and uneven microrelief
– Severe skin depressions and tissue depletion
– Skin lacking adequate thickness, density, and elasticity
– Visible signs of sagging
– A need for more volume in the cheekbones and lips
Usage
To ensure proper dosing, gently press the top of the cylinder (on first use, multiple presses may be required). Allow a small amount of gel to come out and spread a thin layer over the outer area of the right eye and eyelid using the specially shaped applicator. Repeat the same for the left side. Wait 3 minutes, then complete the application by massaging with the shaped tip until the gel is fully absorbed. Important: the gel must be applied to clean skin. Use the product twice a day – in the morning and evening, as described above. To increase the effectiveness of the treatment, it can be used multiple times a day. The treatment lasts about one month. Repeat regularly throughout the year. After each use, clean the applicator with a soft cloth to prevent residue build-up and to maintain proper hygiene of the product.
Technology
NEW TRANSDERMAL TECHNOLOGY
Skin is barely permeable. To enable Fillerina hyaluronic acids and functional molecules to penetrate the epidermis and dermis in a manner similar to molecules injected by aesthetic doctors, Labo researchers developed Transdermic Technology (Swiss Patent CH 711 466). This technology is based on the very low molecular weight of active ingredients, and thanks to this controlled penetration capability, Fillerina products serve as effective, non-invasive alternatives to aesthetic medicine injections.
The percentages below indicate the transdermal penetration of hyaluronic acids and functional active molecules in solution after 24 hours.
TABLE OF ACTIVE INGREDIENT PENETRATION – TESTED WITH FRANZ CELLZ
Hyaluronic Acid Monomer 0.4K Da: 104.47%
Sodium Hyaluronate 0.8K Da: 105.84%
Hyaluronic Acid 1K Da: 96.98%
Hydrolyzed Sodium Hyaluronate 5K Da: 105.35%
Sodium Hyaluronate 20K Da: 105.80%
Hydrolyzed Hyaluronic Acid 50K Da: 104.03%
Sodium Hyaluronate 80K Da: 100.20%
Sodium Hyaluronate 100K Da: 69.20%
Sodium Hyaluronate 200K Da: 55.65%
Sodium Hyaluronate 500K Da: 55.20%
Sodium Hyaluronate 2000K Da: 39.93%
Sodium Hyaluronate Crosspolymer: 27.36%
Hydrolyzed Collagen 2K Da: 101.30%
Hydrolyzed Collagen 12K Da: 95.50%
Soluble Collagen 300K Da: 74.60%
Hydrolyzed Elastin 1.4K Da: 98.38%
Hydrolyzed Elastin 2.2K Da: 97.06%
Palmitoyl Tripeptide-38 (Matrifull): 74.90%
Acetyl Hexapeptide-37: 83.20%
Chondroitin Sulfate: 80.86%
Ingredients
Aqua, Glycerin, Hydrolyzed Glycosaminoglycans, Sodium Hyaluronate, Caprylyl Glycol, 1,2-Hexanediol, Hydrolyzed Elastin, Butylene Glycol, Pentylene Glycol, Sodium Hyaluronate Crosspolymer, Hydrolyzed Hyaluronic Acid, Carbomer, Hyaluronic Acid, Hydrolyzed Collagen, Hydroxypropyl Cyclodextrin, Tropolone, Hydrolyzed Sodium Hyaluronate, Leuconostoc/Radish Root Ferment Filtrate, Decylene Glycol, Arginine, Palmitoyl Tripeptide-38, Sodium Chondroitin Sulfate, Soluble Collagen, Acetyl-Hexapeptide-30, Acetyl Hexapeptide-37, Ethylhexylglycerin, Sodium Hydroxide, Disodium EDTA, Phenoxyethanol, Sodium Chloride, Sorbic Acid, Sodium Benzoate.
The detailed composition can be found on the product packaging.
